Kits available

It’s been a while. But we now have Uzebox JAMMA kits in stock! We are temporarily out of stock of pre-assembled boards but should be back around the Thanksgiving holiday.

Stay tuned for more posts!

Posted in Uncategorized | Leave a comment

Cleaning PCB flux the easy way

Over the past year or two the number of etched PCBs I build has dramatically increased. As we all know build quality is very important; leftover solder flux is very unattractive and has the potential to corrode the board over time. Since I started mass building boards, I have always used the traditional isopropyl-alcohol-toothbrush-scrub-until-your-hand-falls-off method. This method, although very effective and safe on most every electronic component, is quite tedious. It takes me approximately 10 minutes per board to clean, scrub, and rinse several times to achieve complete flux removal. I didn’t have the time or patience to be doing this all day, so I was in need of a quick solution.

I had done some research and found sites like this one that mention the use of a paint thinner brand called Polyclens that would quickly remove the flux with little physical effort. Turns out, Polyclens is not sold in the United States and has been recently discontinued. At this point I decided to take a trip to my local hardware store in search of a suitable replacement to Polyclens. Minutes later I found this paint thinner:

Safer Paint Thinner by Klean-Strip

I tested this product on a few populated flux covered boards once I got home, the results were clear. The board had been stripped of flux and none of the components were damaged by the solution in any way.

Uzebox JAMMA cleaned with paint thinner

Board cleaned with Klean-Strip (Sorry, I don't have a before pic...)

If you wish to try this on your boards, I have some advice:

DISCLAIMER: This paint thinner solution or any other paint thinner solution does contain strong chemicals. Execute safe handling. Anything you do I am not responsible for. Do this at your own risk.

-Before completely soaking your board in paint thinner, ensure that none of the components used on your board will be damaged by the solution. I have experimented with other paint thinners and noticed that the plastic labels on electrolytic capacitors does melt and fall off. So far, this has NOT happened with the Safer Paint Thinner by Klean-Strip I have been using. If you are worried that certain components might be damaged by this solution, test them out by placing several components in a cup filled with the paint thinner or install the components after the board is cleaned.

-If additional flux was applied to the board to help in the soldering process, loosen the flux with some isopropyl alcohol, dry the board, then place the board in the paint thinner. The paint thinner may not be able to remove large amounts of flux at once, so removing most of it will help. It is not exactly necessary to scrub when spraying or pouring alcohol on the board.

-Use a large plastic container and fill the container with just enough paint thinner to cover the entire board. Agitate the solution by letting the paint thinner pass over the board a few times. Flip the board over and repeat the agitation process.

-Once the board appears to be flux free, the paint thinner must be washed off the board. The paint thinner may leave a “sludge” residue behind which can be easily rinsed off. Rinse the board until the sludge has been completely washed away. Light toothbrush scrubbing may be required. I recommend that distilled water be used when rinsing the boards. Non-distilled water works too, but make sure to completely dry the board off.

-Dry the boards once finished. I dry with a cloth then use a shop vac which has a blower at one end to blow water from tight spaces and underneath components. Compressed air can be used as well.

Good luck!

Posted in Electronics, Main | Tagged , , , , , , , , , , | 3 Comments


Stocking up on Uzebox JAMMA Pre-assembled boards:


Posted in Arcade, Electronics, Electronics and tech, Main | Tagged | Leave a comment

Schematic error…

Recently I noticed there was an error in the currently released schematic, the coin counter circuit was drawn incorrectly. Will this affect any currently released Uzebox JAMMA board or the future Revision C board? No, all of the boards have been tested and function properly. The Revision C boards do not have this problem on the PCB.

Below is an image of the old incorrect drawing and the new correct drawing which should replace the old drawing:

I apologize for any inconveniences that may have occurred from this error.
The new Rev C schematic can be downloaded here

PS – Revision C boards are on the way!

Posted in Arcade, Electronics, Main | Tagged , , , , , , , , , , , , , , , | Leave a comment


For those that are interested in developing games for the Uzebox JAMMA using a normal Uzebox console, here is a cross reference for controls.

Posted in Arcade, Cabinet restorations, Electronics, Electronics and tech | Leave a comment


Revision C of the Uzebox JAMMA is on the way. What’s new:

-Added direct connections to Player 1 and 2 buttons 3 and 4. I noticed most JAMMA harness do not include wires for these buttons
-Fixed coin counter problem
-Spaced components near volume adjustment
-Cleaned up traces
-New logo

The Uzebox JAMMA revision C will be available in kit form or pre-assembled in about a month or so from the time of this post.

Posted in Arcade, Electronics, Electronics and tech | Tagged , , , , , , , | Leave a comment

Added Uzebox JAMMA page

Here is a page dedicated for the Uzebox JAMMA.

Posted in Arcade, Electronics, Electronics and tech | Tagged , , , , , , , , , , , , | Leave a comment

It’s here!

The Uzebox JAMMA is ready for sale!

Supplies are very limited… Will re-stock once all have been sold.

Posted in Uncategorized | 1 Comment


Working on documentation as we speak.

Posted in Arcade, Electronics, Electronics and tech | 2 Comments

Uzebox JAMMA Revision B on the way…


The Uzebox JAMMA Revision B is almost completed and ready to be sold As a kit or pre-assembled. Pricing will be announced once the first batch has been completed.

Stay tuned…

Posted in Arcade, Electronics, Electronics and tech, Main | Tagged , , , , , , | Leave a comment